abrasion tester
英 [əˈbreɪʒn ˈtestə(r)]
美 [əˈbreɪʒn ˈtestər]
磨蚀（耗）试验器
双语例句
- Smith's cloth abrasion tester
史密斯织物耐磨试验仪 - Amsler type abrasion tester
阿姆斯拉型耐磨试验仪 - Design of abrasion tester and its data processing system
磨蚀实验台及其数据处理系统的设计 - Wear resistance of the coatings was tested on abrasion tester and the wear appearance of the coatings was investigated by SEM.
在磨损试验机上对其耐磨性进行测试，同时利用扫描电镜对试样的磨损形貌进行观察分析。 - For material plastic, rubber, plywood, glass, painting, textile* etc, this abrasion tester provides a wide range test through different grinding wheel.
简介举凡塑胶、橡胶、合板、玻璃、涂料、纺织等原物料都可使用之泛用性磨耗试验机。 - An impact abrasion tester based on mechanical change of fibers
基于力学性能变化的纤维冲击磨损测试仪 - The micro-scale abrasive wear behaviors of TAMZ alloy were studied using a TE66 micro-scale abrasion tester.
采用TE66试验机对新型TAMZ钛合金的微磨粒磨损行为进行了研究。 - Study on abrasion resistance and wet traction of tire tread by abrasion tester
用室内磨耗试验机研究胎面胶的耐磨性和抗湿滑性 - It can be used to improve the concrete cracking resistance and seepage resistance. Study on abrasion resistance and wet traction of tire tread by abrasion tester
具有改善混凝土抗裂能力、抗冲击抗磨耗能力等作用。用室内磨耗试验机研究胎面胶的耐磨性和抗湿滑性 - Under wet ball mill conditions, corrosive impact abrasion behavior of a newly developed low carbon high alloy steel liner material were researched with a modified MLD-10 wear tester, and comparison with the traditional high manganese steel was made.
采用改进的MLD-10型冲击腐蚀磨损试验机，模拟湿磨工况条件，对新型衬板材质低碳高合金钢和传统材质高锰钢的抗冲击腐蚀磨损特性进行了研究。 - According to the analysis of the performance of antifriction by using abrasion tester, coefficient of friction and wear loss were measured on the conditions of regular feeding oil and no oil.
采用摩擦试验机对所制备的产物的抗磨性进行了表征分析；确定了正常供油状态下和无机油状态下，该纳米抗磨剂的摩擦因数及其磨损量。 - Research on the Sand Slurry Abrasion Tester with Vertical Multi-clamps
多头立式泥沙磨损试验机试验研究 - The effect of varying mates on abrasive wear character of martensitic wear-resistant steel by MLD-10 type impact abrasion tester was investigated.
讨论了在动载三体磨粒磨损条件下，马氏体钢配副变化对磨粒磨损系统耐磨性的影响。 - Abrasion wear test of Fe-20% Cr ahoy with carbon content ranging from 0.82% to 2.94% was conducted at 800 ℃ in a self-made high temperature wear tester. The worn surfaces and subsurfaces were observed by SEM.
本文用自制的高温磨损试验机对碳含量0.82～2.94%的Fe-20%Cr合金进行了800℃下的高温磨损试验，并用扫描电镜观察了磨损面和磨损面亚表面的情况。 - German AG company, with the help of erosive abrasion tester, tested the wear abrasion rate on different abrasion-resistant materials through different erosion angles, velocities and mass flow impact testing samples in different mixing ratio and compared all the abrasion data for analysis.
德国AG公司使用冲蚀磨损试验装置，以不同的冲蚀角、不同的冲蚀速度和不同混合比的料流冲击试验样，测试了不同耐磨材料的磨损率；并对磨损数值进行了分析比较。 - At present, success has been made in material's formula, technology research and project application. Study on abrasion resistance and wet traction of tire tread by abrasion tester
SPUA材料在建筑防水、裂纹修补、防腐、耐磨、抗湿滑、抢修及装饰等工程中具有广阔的应用前景。用室内磨耗试验机研究胎面胶的耐磨性和抗湿滑性 - A high temperature 3 body abrasive wear tester has been developed. It can be used to simulate and study the oxidation and abrasion interaction at elevated temperature. In the temperature range from 700 ℃ to 900 ℃, the tester exhibited good reproducibility.
研制了一台高温三体磨料磨损试验机，可用以模拟研究高温氧化腐蚀和磨料磨损交互作用.该试验机在700～900℃温度范围内具有良好的数据重现性。 - The mechanical properties, abrasion performance and mechanism of the RE/ MoSi_2 composites were investigated by means of friction and abrasion tester, vickers indentation, X-ray diffraction ( XRD), scanning electron microscope ( SEM) and microprobe this paper.
采用磨损试验机、压痕法、X射线衍射仪（XRD）、扫描电子显微镜（SEM）及微探针等研究了稀土/MoSi2复合材料的力学性能、磨损性能及机理。